The paint above the shower is flaking. There’s black mould in the ceiling corner. A customer in Farnborough points up and says, “It must be the roof.”

Sometimes it is. Often it isn’t. So the first thing we look at is the fan.

The culprit may be the fan, the duct behind it, or simply the fact that there isn’t enough air getting into the room for the fan to work properly. An extractor fan is one of the cheapest items in a bathroom renovation, and one that can quietly cause a lot of damage when it’s done badly.

Where does all that shower moisture go?

A shower puts a surprising amount of water vapour into a small room. Warm, wet air has to go somewhere: a properly working fan moves it outside, and fresh air comes in to replace it.

But seal up the double-glazed windows, keep the trickle vents shut and rely on an underpowered fan, and the bathroom can stay humid for hours after everyone’s gone. That moisture settles on the coldest surfaces, often an external wall or ceiling corner. Given time, it can feed mould in grout lines, blown plaster and swollen skirting. Over the longer term, persistent damp can affect floorboards and timber joist ends too.

That doesn’t mean every patch of mould is a ventilation problem, or that one steamy shower is going to ruin your house. It means moisture needs a way out. The Energy Saving Trust’s ventilation advice explains why good airflow helps reduce condensation, damp and mould.

Why the fan can be doing almost nothing

In plenty of homes around Farnborough, the fan has been replaced at some point with a cheap, like-for-like unit. It spins, it makes a noise, everyone assumes it’s doing its job. But the fan is only one part of the system. The route the air takes matters just as much.

We come across a few familiar snags:

  • The duct runs into the loft and stops there, instead of carrying moist air through the roof or wall to the outside.
  • Flexible duct sags in a cold loft, trapping condensation, or gets crushed where someone has stood on it.
  • The duct has come off the back of the wall grille, so extracted air isn’t actually leaving the building.
  • A non-return flap is jammed open or shut.
  • The fan switches off with the light, just when it needs to keep clearing the damp air.
  • There’s no clear path for replacement air because there’s hardly any gap under the bathroom door.

Any one of those can undermine the whole setup. A fan can’t pull air out effectively if it’s fighting a poor duct run or there’s nowhere for fresh air to come in. We’re not trying to turn the bathroom into a draughty wind tunnel. Just giving the air a sensible route in and out.

Isometric illustration of bathroom extractor ventilation with a straight duct running through the loft and out through an external wall

What we check when we survey a bathroom

When we’re planning a bathroom renovation in Farnborough, ventilation gets looked at alongside the rest of the room, not as an afterthought once the new tiles are already on.

First, does the fan run at all? Then, is it suitable for the room’s size, and is it likely to shift enough air once it’s connected to the actual duct run? A fan’s performance on its own isn’t the whole story: bends, length and restrictions in the duct can all affect how well it extracts in practice.

We also check where the duct goes and whether it exits the building properly. We look for a short, reasonably straight run, with rigid duct where practical rather than flexible duct drooping across the loft. We check the shutter, and whether a timer or humidity sensor could help the fan carry on after the light goes out. Finally, we look for a way for replacement air to get in, often a door undercut, with trickle vents kept open.

That’s the practical version. No lecture, just working out what the room needs and what will fit the house.

Better to sort the duct while the ceiling is open

During a refit, we can install a suitable fan, run proper ducting and take it through the wall or roof to an external termination. We can also look at a timer or humidistat, so the fan keeps going after a shower rather than stopping the moment someone switches off the light.

It’s a modest addition to the overall project compared with the cost and hassle of reopening a finished ceiling later. As an indicative guide, not a quote, fitting or replacing a decent fan with proper ducting during a renovation is generally in the low hundreds rather than thousands. The exact work depends on the route and the type of termination needed. The expensive part is often getting access again once the ceiling is finished.

And no, a bathroom refit isn’t mess-free. There’ll be dust and noise, and there can be days without a usable shower while the work is under way. We’ll be straight with you about that. The ventilation work itself adds a morning’s work, not a week, and doing it while the room is already being renovated avoids a separate round of disruption later.

Isometric comparison of a bathroom ceiling corner with condensation and mould beside a clean, dry, well-ventilated corner

Mould or a leak? What the signs can tell you

A black mark in a corner doesn’t automatically mean the roof is leaking. Mould high up, around corners or behind the shower, especially when it gets worse in winter or after showers, can point to condensation. If it wipes away but keeps returning, it’s worth checking whether ventilation is keeping up with the moisture.

A brown ring that grows steadily is a different sort of clue. So is a stain that appears or darkens after rain, damp low down on a wall or under a floor, or a musty smell that never really goes away. Those signs can point to water getting in from somewhere.

There’s no reliable shortcut from a photo to a definite answer. Condensation and leaks need looking at properly, and sometimes more than one issue is involved. We’d much rather find a leak during a survey than halfway through tiling, when the room is already open and the new finish is waiting to go on. If you’re unsure what you’re seeing, our guide to tracking down a hidden leak in Farnborough explains some of the clues we look for.

For more on condensation and damp, the Energy Saving Trust’s guide to fixing damp and condensation is a useful place to start. And if you’re interested in a different kind of bathroom issue, we’ve also written about what older houses can hide behind the tiles in Aldershot.

A few things you can do at home

While you’re working out what needs attention, a few small habits can help shift moisture out of the room:

  • Leave the fan running well after your shower. A timer can do this for you; the Energy Saving Trust suggests keeping extract ventilation on for at least 15 minutes afterwards.
  • Keep window trickle vents open and clear.
  • Open a window briefly after a shower, even in November.
  • Leave the bathroom door ajar afterwards rather than shutting it tight.
  • Wipe down the worst of the water on tiles or glass.
  • Don’t paint over mould and treat it as fixed. If it keeps coming back, the moisture source still needs attention.

Those steps can help, but they won’t make a blocked duct work or send a loft’s worth of damp air outdoors. If the mould returns, it’s time to check the whole ventilation route.

Get the ventilation right as part of the renovation

A fresh bathroom should feel good to use, not just look smart on the day the last bead of silicone goes on. That means planning where the moisture goes as carefully as we plan where the shower and vanity sit.

We cover the whole job, from planning through to that final silicone bead, and we work across Aldershot, Farnborough, Farnham, Guildford and surrounding areas. You can find out more about our bathroom renovation service, then book a visit or survey at a time that works for you.

Isometric illustration of a finished modern bathroom with a walk-in shower, grey vanity unit and an extractor fan in the ceiling